Welcome to WaterFiltersFAST.com
Security Seals

  • Visit Us Socially
  • WaterFiltersFAST.com Facebook
  • WaterFiltersFAST.com Google +
  • WaterFiltersFAST.com Twitter
0 item(s) - Total: $0

Dow Filmtec LE-440i 40 inch x 8 inch Low Energy Membrane

Dow Filmtec LE-440i 40 inch x 8 inch Low Energy Membrane

Item SKU: LE-440i

MFG ID: LE-440i | UPC:

Dow Filmtec LE-440i 40 inch x 8 inch Low Energy Membrane

The Filmtec LE-440i element is a low-energy element featuring the highest active membrane area in the industry. It enables high productivity and low energy operation, while maintaining high-rejection performance, minimizing operating expense and lowering the total cost of water for industrial and municipal applications.


  • Delivers the same permeate flow at an equivalent operating flux at 40% lower feed pressure, compared to the Filmtec BW30-440i element.
  • Offers permeate flow rate 10 percent higher while producing similar permeate quality than that of the Filmtec LE-400 element, enabling the lowest total cost of water in high-purity industrial applications.
  • Includes iLEC interlocking endcaps, which reduce system operating costs and the risk of o-ring leaks that cause poor water quality.
  • Designed using an industry standard 1.125 inch ID permeate tube for interchangeability with other brackish water elements.


  • Membrane Type: Polyamide Thin-Film Composite (TFC)
  • Maximum Operating Temperaturea: 113?F(45?C)
  • Maximum Operating Pressure: 600 psi (41 bar)
  • Maximum Pressure Drop: 15 psi (1.0 bar)
  • Maximum Feed Flow Rate: 85 gpm (19 m3/hr)
  • pH Range, Continuous Operationa: 2-11***
  • pH Range, Short-Term Cleaning: 1-13* (30min)
  • Maximum Feed Silt Density Index: 5 SDI
  • Free Chlorine Tolerancec: <0.1 ppm
  • Permeate Flow Rate: 12,650 GPD (48 m3/day)*
  • Stabilized Salt Rejection: 99.3%

*Permeate flow and salt rejection based on the following standard conditions: 2,000 ppm NaCl, 150 psi (10.3 bar), 77°F (25°C), pH 8 and 15% recovery. For comparison, the LE-440i will have a permeate flow of 13,400 gpd (51 m3/d) and stabilized salt rejection of 99.3% when normalized to a feed solution of 1,500 ppm NaCl as used by some manufacturers. Flow rates for individual elements may vary but will be no more than 15% below the value shown.

**Under certain conditions, the presence of free chlorine and other oxidizing agents will cause premature membrane failure. Since oxidation damage is not covered under warranty, Dow recommends removing residual free chlorine by pretreatment prior to membrane exposure. Most RO systems have carbon pre-filters for this purpose.

***Maximum temperature for continuous operation above pH 10 is 95F (35C).

Note: Active surface area guaranteed +/-3%. Active area as stated by Filmtec is not comparable to nominal membrane area often stated by some manufacturers.

Question & Answers

Q Why did you choose this?
Product Video
Related Products, Parts & Accessories
Dow Filmtec TW30-1812-75 75 GPD Thin Film Composite Dry Residential Membrane
Product Thumbnail
Dow Filmtec BW30-365 40 inch x 8 inch Tap and Brackish Commercial Membrane
Product Thumbnail
Dow Filmtec LE-400 40 inch x 8 inch Low Energy Membrane
Product Thumbnail
Dow Filmtec HRLE-440i 40 inch x 8 inch Low Energy Membrane
Product Thumbnail
Dow Filmtec SW30HRLE-4040 40 inch × 4 inch Sea Water Desalination Membrane
Product Thumbnail
Dow Filmtec RO-4040-FF 40 inch × 4 inch Sanitary/Full Fit Medical Food Membrane
Product Thumbnail